how to make hypertufa pots without peat moss

Make Your Own Hypertufa Container

Step 1. Measure and mix the peat moss, perlite, cement, and a small handful of reinforcing fibers in your tub. You'll kick up plenty of dust at this stage, so be sure to wear your dust mask. Add the water while stirring with your trowel. Test the consistency frequently, as it's much easier to add water than it is to readjust the dry ...

How to Make a Sustainable Hypertufa Container

Video: Christine Alexander. This video shows how to make a sustainable hypertufa container. These troughs are typically molded using a mixture of portland cement, perlite, and peat moss, but in this tutorial, I'll be …

Oh, the Possibilities ! Draped Hypertufa Pots

You can drill holes in the draped hypertufa pots very easily with a drill after it is cured. Use a masonry bit. Recipe on this one is heavy on the cement. I would use: 1 part Portland cement (I was using a 2 qt pitcher) 1/4 part of peat ( about 1 pint) a handful of vermiculite and mortar mix depending on how much you want it to be textured.

Use hypertufa to make containers that look like stone

Plan to make a lot of hypertufa pots, or have a party. 3 parts perlite. Measure the ingredients by volume with a bucket. Put on gloves and mix by hand in a cement tray (plastic and inexpensive), wheelbarrow or other large container. Add water gradually and mix with ingredients until it is stiff and holds together, about like cookie dough or ...

Hypertufa Troughs

Place it in a plastic bag and place it in a sheltered spot, out of direct sunlight. Overheating in the sun can cause hypertufa to cure unevenly and crack. The plastic allows the mixture to dry slowly and …

How to Make Hypertufa Pots

It should be at least an inch thick. Press firmly against the bottom getting out all air pockets and compressing the wet mix. After the bottom seems full and compressed, start putting big handfuls against the sides and doing the same. Press and firm it up the sides as you go, pulling on the plastic firmly.

How to Make a Hypertufa Trough for a Faux Stone …

Allow container to dry. 2. Fill. Place a piece of wire mesh over drain holes to allow water to drain without losing soil and to prevent slugs from creeping into the trough. Make a planting mix that holds moisture and drains well by combining equal parts humus, peat or leaf compost, and sand. 3.

Hip Hip Hypertufa

4. Holding the drainage hole plug in place, push a handful of wet hypertufa mixture firmly against the bottom of the mould. Repeat until you have made a bottom base that is approximately 2.5cm ...

Garden Guides | How to Make Peat Moss Flower Pots

For large pots, spread up to a 2-inch layer on the mold. Mix the ingredients for the flower pot in a bucket or wheelbarrow. For small pots, spread a 3/4-inch layer of the mixture on the mold. Use a trowel to smooth the mixture and blend any seams into each other. Make the bottom of the pot as flat as you can using the trowel.

Hypertufa How To; all about making hypertufa projects

Carefully add in small increments, mixing well between: Water – straight out of the tap or rainwater. Additionally, you can add a small amount of: Hydrated lime – adds plasticity, the ability to hold its shape while being molded. This would be used when sculpting or making the hypertufa in a mold without much support as it will resist ...

Hypertufa Pots

Hypertufa Pots How-To . 1. Wearing rubber gloves and a dust mask to avoid breathing cement dust, mix 3 parts perlite, 3 parts peat moss, and 2 parts Portland cement in a plastic tub. If desired, add cement pigment for color. If making a large pot, add acrylic fibers for strength.

How to Make Quirky Hypertufa Planters

*NOTE: To make this project in hypertufa, add a mix of 2 parts perlite, 2 parts peat moss, 1.5 parts Portland cement, and enough water to have it just stick together. Mix well and adjust the ingredients as needed until you can form a ball in your hands that sticks together without being able to squeeze water out. Make it! First, decide on a shape.

How To Make Hypertufa Pots and Faux Stone Planters

Start on the inside of the cooler and then work in sections. Use your brush to paint a thick layer of paint over the entire inside of the cooler. Now take a handful of sand and wipe it over the painted surface so it sticks well. Repeat until the walls and bottom of …

Your Sphagnum Peat Moss Is A Solid Block! Now What?

It is really simple. Just cut a hunk of the peat moss bale and place it in a container. Use a big container because the peat moss will hold lot of water. Your container will need to be a type which can have boiling water poured into it. Lay the chunks in and pour the water on top. You will quickly see the water gone! Pour more.

How to Make Hypertufa Planters

Building a Hypertufa planter: You require two coated cardboard boxes of different sizes so that the small box can fit inside the bigger one. There should be a 5 to 6 cm dense Hypertufa mix between the two boxes so that the wall is thick enough for the boxes to function as the mold. You can create a square or rectangular tub in this manner.

How to Make a Hypertufa Planter or Pot | Gardener's …

1 part Portland cement. 1.5 parts peat moss. 1.5 parts perlite. Water. Tub for mixing ingredients. Rubber gloves. Dust mask. 2 cardboard boxes, one about 2" smaller than …

Hypertufa Face Pots or Grots : 3 Steps (with Pictures)

Step 3: Making TheFace. Making the face. Now I mix a a batch of tufa normally a half a coffee can of sand, Portland cement and peat moss. I first paint on some acrylic admix to the pot just because I have some. I've made these for years without it. I also make this a little wetter the the pot mix.

How To Make Hypertufa Planters

Hypertufa Pots How-To. 1. Wearing rubber gloves and a dust mask to avoid breathing cement dust, mix 3 parts perlite, 3 parts peat moss, and 2 parts Portland …

How to Make Hypertufa Garden Planters and Containers

Remove the mold or container. Re-wrap your container, and place it in a shady place for another two days. After the 48 hours, unwrap it and soak it with a hose periodically over the next couple of weeks to leach out the residual lime from the cement, which is toxic and will harm plants. Remember to be patient.

Video: Making the Draped Hypertufa Planter! So Easy!

8 quarts Portland cement and the 1 extra cup. 2 quarts vermiculite (fine) 2 quarts peat moss well sifted. water to mix to the right consistency. cloth scraps (old towel, napkin, washcloth, any fabric) your "tower" you will drape it over, needs to be high enough to allow the tips to "dangle. plastic to cover this "tower" so that the ...

Hypertufa trough planter

To make an 18 x 12 x 9-in. planter, you need approximately 2 gallons of sifted peat, 2 gallons of perlite, 1-1/3 gallons of Portland cement (about 12 lb.), 1 cup of loosely packed reinforcing fibers, and water. To test for the …

How to Make Hypertufa

I prefer a bussing tub, which is around 4" deep to prevent the materials spilling over the sides. Pour in equal parts of peat moss and perlite, followed by the Portland cement. You can alter this ratio slightly to fit for …

How to Make a Freeform Hypertufa Planter

Instructions. Combine the cement, peat moss and vermiculite in a large plastic tub. Slowly add water and mix with your hands until you can make a ball with the mix that holds together. Place a handful on a …

How to Make Hypertufa Planters & Troughs

a recipe without peat. Hypertufa is made of equal parts of cement, sharp sand (or perlite) and peat moss or coconut fibre . See fig 1. Please keep in mind that cement isn't at all environmentally friendly. To reduce my carbon footprint, and make a planter without peat, I tend to use left-over cement from other projects.

Hypertufa Index Page | The Hypertufa Gardener

Hypertufa – Fall in love with these ancient-looking stone planters. These garden planters are called hypertufa. Aged-stone-looking garden planters can be made with hypertufa which is a mixture of Portland cement, vermiculite, (or perlite) and peat moss. This mixture cures into a stone-like material that is heavy and durable but lighter than ...

Hypertufa: Make Tough Lightweight Homegrown Pots …

No exact amount of water can be given. It should be a little less than, rather than equal to, the volume of the dry ingredients. Add a little amount of water after another until it meets the desired consistency. Some people like their hypertufa to be of cottage cheese consistency while others prefer wet.

How To Make Hypertufa Pots Recipe | Balcony Garden Web

Step 2: Mix the Dry Ingredients. Mix equal amounts of Perlite, Peat moss, and Portland cement in a large container for the right DIY Hypertufa Pots Recipe. Do wear protective gear like gloves and mask while mixing. Break the large clumps to create a smooth, homogenous mixture.

Hypertufa Pots

The first step involves making a uniform and smooth mixture of peat moss, Portland cement and sand, perlite or vermiculite in the proportion of 2:1:1. You can use a little water to wet the mixture so that it is only slightly seen when pressed with your hand. Selecting an appropriate mold constitutes the second step.

How to make a simple hypertufa trough

3 parts vermiculite. 3 parts peat moss. 1-2 cups of dye (depending on the color you are hoping to achieve) 3-4 cups of 'fluffed' synthetic fibers (this will translate to about a 1/4 cup unfluffed fibers). …

How to Make a Hypertufa Planter | HGTV

Get easy steps to create these beautiful and inexpensive containers in any size and shape you like. Image courtesy of Ben Rollins. Hypertufa planters are a lighter …